Shopping Cart Shopping Cart - 0 item(s) / Total: $0
Home > HERMS coils Custom coils > 3/8" Coils

8" Coil with 2 vertical bends 25' x 3/8" x .035 OD Tubing 304/304L HERMS/Fermentor coil

Part Number 11A03X8252V
review 2 Review(s)
5
8" Coil with 2 vertical bends 25' x 3/8" x .035 OD Tubing 304/304L   HERMS/Fermentor coil
Email a friend Email a friend
Write a Review Write a Review
Price
Your Price:  
$54.59
Quantity
Add to Gift Registry
Description

This coil has two vertical bends going up.  This configuration is not only used for HERMS systems where brewers don't want to drill a hole in the sidewall but fermentors as well.  The coil can be submersed in a fermentor through the lid and glycol or cold water is pumped through the coil to maintain the temperature.  The tubing is made out of 304/304L stainless and is measured 3/8" OD  (Outside Diameter).  This coil has a 8" Outside Diameter and the height is made per your request.  You must note in the comment section upon checkout the overall height from bottom coil to top connections. If you would like spacing between the coils for easy cleaning, please note this in the comment section as well.  No additional comments will leave the coil compressed for shipping and customer can space coils to their requirements.

Using a HERMS coil eliminates the need for a burner under your mash to maintain temperature and it will also help clarify your wort.  While you mash, your wort will travel through the coil which is installed in your HLT (Hot Liquor Tank).  The HLT will be hot and ready for sparging so you can also maintain your mash temperature with this as well.  While your running your wort through your coil your also filtering giving you great clarity.  HERMS systems help increase your efficiency and get you the original gravity your trying to achieve.

That's not all a HERMS coil can do, it can also cool!  Simply fill your HLT with ice and you've creating a cooling coil!

The maximum overall height listed in our shopping cart is set at 20"  Coils with any additional height will require a larger box which can increase shipping costs 
























Customer Reviews
Rating Beautiful Coil
 
Using in a 15 gallon RotoMold Tank. I sent them this for size measurements, and it fit great. Sits so low in the cone I could do 5 gallon batches, but still doesn't touch the plastic. Coil is beautiful and made out of good quality stainless. Shipping was faster than expected, I think a little under 1 week. Not bad at all for a custom made item. Make sure to get mounting hardware for 3/8! "Bottom of coil to top of lead: 17". Please add spacing for CIP. Please make the vertical leads on opposite sides. This is intended to be a top-hanging fermeter cooling coil."
  Did you find this helpful?    3 of 3 Found Helpful
Reviewed by: (Verified Buyer)  from San Diego. - 12/30/2015
5/5
Rating home brewer
 
The product arrived quickly and exactly as requested. I accidentally specified the wrong size bulkhead fittings....received an email from Stainless Brewing just prior to shipping asking if I would prefer the correct size. Of course I did and they shipped the proper size. Couldn't be happier with the product and the customer service.
  Did you find this helpful?   
Reviewed by: (Verified Buyer)  from Fort Collins, CO. - 3/21/2017
5/5
Related Items
Compression x Male Bulkhead Connector with Gasket and Washer
Compression x Male Bulkhead Connector with Gasket and Washer
Average Rating 10 Review(s)
Your Price: $13.84
1/2
1/2" Compression x 1/2" Male NPT weldless Bulkhead fitting
Average Rating 1 Review(s)
Your Price: $16.49
 
Recently Viewed Items